NEOFAB Non-woven, Polyester Fabric for Reinforcing Waterproofing Coating

Public Channel / Data Sheets

Non-woven, Polyester Fabric for Reinforcing Waterproofing Coating

NEO-FAB is made up of continuous, synthetic, polyester fibers joined
mechanical needle-punch procedure. It is particularly recommended for
strengthening waterproofing liquid membranes.

This special fabric enhance properties of liquid applied membranes like
toughness, punchresistance, ultimate elongation and crack bridging.

ADVANTAGES
- Remains unaltered and is resistant to alkalis contained in cement.
- Resistant to atmospheric agents.
- Dimensionally stable.
- Light and easy to handle.
- Easy to cut.
- May be adapted to the profile of all types of substrate.

TECHNICAL CHARACTERISTICS
NEO-FAB is a non-woven fabric, which makes it completely permeable
to water, and enhances the bond between the first and second layer of
liquid waterproof membranes in which it is embedded.

WHERE TO USE
Reinforcement in polyester fabric used together with liquid applied or flexible
cementitious membranes for waterproofing and protecting concrete surfaces,
and concrete units particularly subject to large deformations and, therefore,
at risk of cracking.

APPLICATION PROCEDURE
The surface on which NEOFAB is to be applied must be sound and
perfectly clean. Remove all cement laitance, parts and traces of powder,
grease, oil and release agents by sandblasting or washing down with
high-pressure waterjets.

Share on Social Networks

Share Link

Use permanent link to share in social media

Share with a friend

Please login to send this document by email!

Embed in your website

Select Link to start with 

2. TDS - WP - WS1 - 000_01 / 21 PHYSICAL PROPERTIES Properties Standard Unit Test Result Mass/ Unit Area ASTM D 5261/EN ISO 9864 gms/m2 70 Thickness (2kN/m2) ASTM D 5199/EN ISO 9863 - 1 mm 0.70 MECHANICAL PROPERTIES Wide Width Tensile Strength (MD) ASTM D 4595/EN ISO 10319 kN/m 2.5 Wide Width Tensile Strength (CD) ASTM D 4595/EN ISO 10319 kN/m 2.0 Wide width Tensile Elongation (MD) ASTM D 4595/EN ISO 10319 % >45 Wide width Tensile Elongation (CD) ASTM D 4595/EN ISO 10319 % >45 Puncture Strength (CBR) ASTM D 6241/EN ISO 12236 N 500 HYDRAULIC PROPERTIES Opening Size (O95) ASTM D 4751 mm 0.212 (70) Flow Rate – 5 cm head EN ISO 11058 l/m2/s 120 Permittivity ASTM D 4491 Sec - 1 2.4 ROLL DIMENSIONS Roll width m As per Need Roll Length m 50 Roll Area m2 As per Need All values are subject to 5 - 10 % tolerance The surface on which NEOFAB is to be applied must be sound and perfectly clean. Remove all cement laitan ce, parts and traces of powder, grease, oil and release agents by sandblasting or washing down with high - pressure waterjets. Measure the area of application & then cut the NEOFAB fabric as per requirement. In case of applying together with liquid applied waterproofing membranes, follow the guideline provided by membrane manufacturer. While our general recommendation is as: 1. Prepare the liquid membrane by mixing of its components. 2. Apply the first coat of membrane on surface. 3. While the pr oduct is still fresh, carefully lay the NEOFAB on the surface, and press it firmly using a flat - bladed trowel to make sure that it is perfectly wetted. 4. Application of a uniform thickness second layer of membrane, in order to completely cover the NEOFAB. 5. Ad jacent sheets of NEOFAB must overlap by at least 5 cm at both the longitudinal and transverse junction points. APPLICATION PROCEDURE NOTE: The information contained in this DATA SHEET, as well as our advice, both written as oral or provided through testing, are based on our experience, and they do not constitute any product guarantee for the installer, who must take them as simple orientations, provided strictly as information. W e recommend to study deeply all information provided before proceeding to the use or application of any of our products, and strongly advise to conduct tests “on - site” in order to determine their convenience for a specific project. Our recommendations do n ot exempt of the obligation that installers have to deeply know the right application method for these systems before they use them, as well as to conduct as many preliminary tests as possible if there are any doubts about the appropriate system to use. Th e application, use and processing of our products are beyond our control, and therefore under the exclusive responsibility of the installer. In consequence, the installer will be the only responsible of any damage or prejudice derived from the partial or t otal in - observation of our indications, and in general, of the inappropriate use or application of these materials. Saja a Industrial Area behind Sharjah Cement Factory, Sharjah U.A.E. Email: Inquiry@royalwayindustries.com PO BOX: 65034 Tel: +971 6 5679000 Website: www.royalwayindustries.com R OYAL WAY INDUSTRIES LLC Page 2

1. TDS - WP - WS1 - 000_01 / 21 PROPRETIES C H AR A C TERISTICS NEO - FAB is made up of continuous, synthetic, polyester fibers joined mechanical needle - punch procedure. It is particularly recommended for strengthening waterproofing liquid membranes. This special fabric enhance properties of liquid applied membranes like toughness, punchresistance, ultimate elongation and crack bridging.  Remains unaltered and is resistant to alkalis contained in cement.  Resistant to atmospheric agents.  Dimensionally stable.  Light and easy to handle.  Easy to cut.  May be adapted to the profile of all types of substrate. NEO - FAB is a non - woven fabric, which makes it completely p ermeable to water, and enhances the bond betwee n the first and second layer of liquid waterproof membranes in which i t is embedded. ADVANTAGES NEOFAB Non - woven, Polyester Fabric for Reinforcing Waterproofing Coating Page 1 TECHNICAL CHARACTERISTICS Reinforcement in polyester fabric used together with liquid applied or flexible cementitious membranes for waterproofing and protecting concrete surfaces, and concrete units particularly subject to large deformations and, therefore, at risk of cracking. S ome application examples  Large - scale containment basins.  Retaining walls.  Foundations.  Hanging gardens.  Flat roofs.  Swimming pools.  Bathrooms and shower booths cubicles/wet rooms.  Terraces. WHERE TO USE

Views

  • 3203 Total Views
  • 2474 Website Views
  • 729 Embeded Views

Actions

  • 0 Social Shares
  • 1
  • 0
  • 0 Comments

Share count

  • 0  Facebook
  • 0  Twitter
  • 0  LinkedIn

Embeds 5

  • 61 www.sab-us.com
  • 15 161.97.92.48
  • 5 161.97.92.48:8011
  • 144 www.google.com
  • 8

Website Visitors - 503604