Public Channel / Data Sheets

Two Component Polymer Modified Flexible Cementitious Waterproof Coating

SAB® modiflex CW 216:
Is a two-component polymer modified cementitious coating. The product
may be trowel or brush applied to provide a flexible waterproof barrier.

Usage:
SAB® modiflex CW 216 may be used where there is a requirement to exclude water from
a building or retain it within a structure. The material is particularly effective for

• Pile head waterproofing.
• Water proofing of potable water reservoirs, both interior and exterior.
• To provide protection for concrete against carbonation and chloride attack.
• Waterproof coating for roofs, concrete water tanks, lift well, inspection pits,
swimming pools spillways, bathrooms, kitchens and other wet areas.
• Waterproof lining for water retaining structures
• General construction waterproofing. As a protective coating for foundations.
• As a backing to marble and granite to prevent water ingress and thus alleviate
surface staining protection against brackish water
• Coating sea water channels
• Protection of concrete against carbonation and chloride ion attack

ADVANTAGES
• Excellent performance and flexible in nature, Good adhesion to most surface
• Non-toxic therefore suitable for potable water.
• Resistant to carbon dioxide and chloride ion diffusion. (Forms a film that
provides an anti-carbonation coating over concrete.
• Can resist up to 7 Bars of pressure. • Unlike conventional coatings which
require 7 to 28 days cure of concrete, SAB®modiflex CW 216 can be applied to
24 hours old concrete, thereby giving immediate protection to the concrete.
• Allows the substrate to breath.


PACKING AND STORAGE

Store out of direct sunlight, clear of the ground on pallets, protect from rainfall. Avoid excessive compaction. Shelf life is 12 months when stored as above. Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging

PACKAGING
Available in 20 kg kits.
Part A: 15 kg powder
Part B: 5 kg liquid.
COVERAGE
1.7 to 1.8 kg / m² / 1 mm thickness

Share on Social Networks

Share Link

Use permanent link to share in social media

Share with a friend

Please login to send this document by email!

Embed in your website

Select Link to start with 

3. Treat any splashes to the skin or eyes with fresh water immediately. Should any of the products be accidentally s wallowed, do not induce vomi t ing and call for medical assistance immediately. There are no known health hazards associated with SAB ® modi flex CW 216 PACKING AND STORAGE Store out of direct sunlight, clear of the ground on pallets, protect from rainfall. Avoid excessive compaction. Shelf life is 12 months when stored as above. Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging PACKAGING Available in 20 kg kits. Part A: 15 kg powder Part B: 5 kg liquid. COVERAGE 1.7 to 1.8 kg / m² / 1 mm thickness

2. Technical data SAB ® modi flex CW 216 (The properties shown above were obtained under laboratory conditions). All values given are subject to 10% tolerance CHEMICAL RESISTANCE: SAB ® modi flex CW 216 is resistant to chemical solvents & oils. Color Grey (Colors on request) Drying time 3 hours Specific Gravity 1.85 Tensile Strength (N/sqmm) 1.2 (+/ - 0.2 ) Elongation (%) 60 (+/ - 10 ) Toxicity Non - Toxic Hydrostatic pressure @ 5bar (50m) Pass PREPARATION OF SURFACE The surface must be sound and free of oil, grease, dust and other unwanted residual material which will affect the bonding. The surface to be treated should be saturated with water prior to application but no standing water should be present. Mixing The material is supplied in two parts, and premeasured. On site mixing is needed. Take the liquid in a container and slowly add the powder to the liquid and mix using a slow speed drill fitted with a suitable paddle until a lump free creamy consistency is obtained. Do not mix more material than that can be used within 45 minutes. Never add water to loosen the material at any stage. APPLICATION AND CLEANING OF TOOLS Apply the first coat using enough material at a rate of 1 kg /m² to completely cover the holes, cracks etc. A soft bristled brush or trowel can be employed for this. Once the first coat is dry, apply second and third coat to achieve the required thickness at an average rate of 0.7 to 0.9 kg/m² per coat. If necessary, embed an adhesive primer into the first coat and apply the second coat on top of it. HEALTH AND SAFETY As with all construction chemicals products caution should always be exercised. Protective clothing such as gloves and goggles shall be worn.

1. SAB ® modiflex CW 216 Two Component Polymer Modified Flexible Cementitious Waterproof Coating Description SAB ® modiflex CW 216: Is a two - component polymer modified cementitious coating. The product may be trowel or brush applied to provide a flexible waterproof barrier. Usage : SAB ® modiflex CW 216 may be used where there is a requirement to exclude water from a building or retain it within a structure. The material is particularly effective for • Pile head waterproofing. • Water proofing of potable water reservoirs, both interior and exterior. • To provide protection for concrete against carbonation and chloride attack. • Waterproof coating for roofs, concrete water tanks, lift well, inspection pits, swimming pools spillways, bathrooms, kitchens and other wet areas. • Waterproof lining for water retaining structures • General construction waterproofing. As a protective coating for foundations. • As a backing to marble and granite to prevent water ingress and thus alleviate surface staining protection against brackish water • Coating sea water cha nnels • Protection of concrete against carbonation and chloride ion attack ADVANTAGES • Excellent performance and flexible in nature, Good adhesion to most surface • Non - toxic therefore suitable for potable water. • Resistant to carbon dioxide and chloride ion diffusion. (Forms a film that provides an anti - carbonation coating over concrete. • Can resist up to 7 Bars of pressure. • Unlike conventional coatings which require 7 to 28 days cure of concrete, SAB ® modi flex CW 216 can be applied to 24 hours old concrete, thereby giving immediate protection to the concrete. • Allows the substrate to breath.

Views

  • 2600 Total Views
  • 1984 Website Views
  • 616 Embeded Views

Actions

  • 0 Social Shares
  • 2
  • 0
  • 0 Comments

Share count

  • 0  Facebook
  • 0  Twitter
  • 0  LinkedIn

Embeds 3

  • 14 www.sab-us.com
  • 13 161.97.92.48
  • 4 161.97.92.48:8011

Website Visitors - 510851