SBS modified highly flexible bituminous membrane with a plain surface.
A high performance elastomeric waterproofing membrane which combines the ability to withstand high ambient temperature with the usual characteristics of a SBS membrane of high flexibility at low temperature that makes it easy to apply at sub-zero temperature
2. www.middleeast.weber 2/2 Technical data sheet . Edition: 06.20 -A Properties Typical Values Test Method Thickness Reinforcement base Tensile strength - long - trans Elongation - long - trans Lap joint strength - long - trans TEAR RESISTANCE - long - trans Low temperature flexibility* Puncture Resistance Softening point Water Absorption (n/a slate) Penetration (at 25 º C) water vapour transmission Heat resistance Reaction to fire Biflex membranes are resistant to chlorides, sulphates and phosphates found in ground water 4.00mm 180 gms/m² non woven spun bond Polyester mat 750 N/5 cm 580 N/5 cm >40% >50% 750 N/5cm 650 N/5 cm 450 N 400 N -5 º C L3 1000 153 º C <0.4% 22 dmm 0.5 gm/m2/24Hr > 125 F EN 1849-1 ASTM D 5147 ASTM D 5147 ASTM D 5147 ASTM D 5147 UEATC M.O.AT 30 UEATC M.O.AT 30 ASTM D5147 ASTM D5147 ASTM E 154 ASTM D 36 ASTM D5147 ASTM D5 ASTM E 96 ASTM D 5147 EN 13501-1 DISCLAIMER While the company guarantees its products against defective materials, the use and application of these products are made without guarantee since the conditions of their application are beyond its control. It is recommended to verify with the company that the product is suitable for the intended use, and that this Data Sheet version is the latest one. The company may modify it without prior notice. Technical characteristics are listed for guidance only. For more information, please contact the company’s office in your location. NOTE The information included on this Technical Data Sheet is the sole property of Saint-Gobain Middle East Holding SAL (previously SODAMCO Holding). The unauthorized disclosure, use, dissemination or copying (either whole or partial) of this data sheet or any information it contains, is prohibited and subject to legal pursuit. Biflex PL 4mm/180 * Values subject to a variation of ± 20% * Different cold flexibility value can be supplied to special order WATERPROOFING
1. PACKAGING GENERAL A high performance elastomeric waterproofing membrane which combines the ability to withstand high ambient temperature with the usual characteristics of an SBS membrane of high flexibility at low temperature that makes it easy to apply at sub-zero temperature. It is suitable for all types of waterproofing works including roofs, terraces, car parks, pile capping, foundation works, basement tankings, where high flexibility and malleability are required. SPECIAL FEATURES • Positive vapour barrier to water and dampness. • Excellent resistance to atmospheric agents. • High flexibility during application at sub-zero temperature with no physical strains. • High malleability making it entirely suitable for difficult basement and foundation works. • High softening point allowing it to maintain shape stability at high temperatures. • Withstand thermal shocks. • Accommodates structural movements. • Resistant to chemical attacks and suitable for areas subject to seaside salinity SIZE AND SURFACE FINISH Biflex PL 4mm/180 is supplied in 1 m wide and 10 m length. The surface finish is either sanded or protected with PE film.. REINFORCEMENT CORE AND COATING MIXTURE Biflex PL 4mm/180 waterproofing membranes is reinforced with 180 grams non woven spun bond polyester reinforcement that gives the membrane dimensional stability and resistance to puncture. It is coated with a specially formulated mixture of SBS modified bitumen which makes the membrane resistant to water, atmospheric agents, and malleable at low temperature while retaining a high softening point. INSTRUCTIONS FOR USE The membrane must first be unrolled and laid down on the area to which it is to be applied. Check the orientation carefully. Adjacent rolls should then be laid, each overlapping the one next to it by 10 cm on the side and 15 cm at the ends. Taking care not to change the orientation of each roll, reverse the process until each has been re-rolled. When laying the roll, the lower surface should be heated with a propane torch, using sweeping left to right movements. This will melt the lower surface of the membrane and allow it to stick to the substrate... Continue this process for each subsequent roll, remembering that the overlaps must be 10 cm for the edges and 15 cm at the ends. When the process is complete, carry out an inspection to ensure total adhesion. When applied in a totally bonded system, a coat of dry prime WB or dry prime SB should be applied at the rate of 200 – 300 g/m². Allowed the primer to dry thoroughly,in time of high humidity we recommend it should be left overnight. www.middleeast.weber 1/2 Technical data sheet . Edition: 06.20-A SBS modified bituminous membrane - Plain Leb Syria Jordan UAE Qatar Kuwait KSA Oman 1x10 m 1x10 m 1x10 m 1x10 m 1x10 m 1x10 m 1x10 m 1x10 m WATERPROOFING Biflex PL 4mm/180 Formerly "Biflex PL"
Views
- 3259 Total Views
- 2461 Website Views
- 798 Embeded Views
Actions
- 0 Social Shares
-
0
-
0
- 0 Comments
Share count
-
0
Facebook
-
Twitter
-
0
LinkedIn
Embeds
4
-
119
www.sab-us.com
-
2
www.google.com
-
10
161.97.92.48
-
9
161.97.92.48:8011