Elastomeric Waterproof & Protective Coating Based
on Polyurethane Dispersion (PUD)
Elastomeric Waterproof & Protective Coating Based
on Polyurethane Dispersion (PUD)
BAUCOAT HP is a liquid applied elastomeric
waterproof and protective coating based on
polyurethane dispersion (PUD)
The polyurethane is modified with specially
selected polymers to form a tough, flexible and
durable coating. It is completely free of
Waterproofing or vapor barrier protection of
exposed roofs, domes, terraces, balconies,
corrugated sheets and wet areas like kitchens,
bathrooms & toilets
• Ready to use / apply single component
• Forms a highly elastomeric, tough and
• Environment friendly
• Fast surface hardness, no tack surface, low
• Excellent crack bridging properties
• Exhibits high resistance to weather
conditions and good resistance to UV
• Good adhesion and elastic recovery.
Excellent resistance to water and vapor.
• Good chemical resistance against diluted
acids, oil, salts, bacteria and common fuels.
Color White, Green, Grey (As
Solid Content [%] > 60
SRI (Solar Reflective Index) > 80 (White)
Elongation [%] 400 (+/- 30)
Tensile Strength [N/mm²] 2 (+/- 0.2)
Pull Off Adhesion [N/mm²]
(at concrete failure) 1.20
Peel Off Adhesion [N/mm] 2.0
Crack Bridging [mm] 1.5
Hydrostatic Pressure @ 5bar (60m) No leakage
Chemical Resistance Dilute acids & alkalis,
Full cure [days] 7
Application Temperature [°C]5 to 35
Service Temperature [°C] -20 to 70
(The properties shown below were obtained under
All values given are subject to 10% tolerance
Surfaces must be cleaned and made free of dust,
dirt, moss, oil, grease and other loose particles.
This can be achieved by grit/sand/shot blasting.
As a minimum, vigorous wire brushing should be
employed. All pin holes and surface defects shall
be repaired with a suitable concrete repair
BAUCOAT HP does not require priming as such
and can directly be applied onto the substrate
surface. In case of highly porous surface, a
priming coat is recommended to seal the pores
and stabilize the surface.
The primer coat can be produced on site by
diluting BAUCOAT HP with water (20% by
weight) . Apply the primer coat @ 4m²/ Kg and
allow to dry.
The primer coat also functions as an adhesion
promoter for the top coats. It can be applied by
a brush, roller or airless spray and allowed to dry
completely before the application of subsequent
BAUCOAT HP is a single component product but
mix the contents of the pail thoroughly prior to
application to remove any sediment. A slow
speed drill and suitable paddle mixer shall be
used to avoid the formation of air bubbles.
The coating can be applied with a brush, roller or
airless spray and shall be applied in a minimum
of 2 coats. Apply the first coat of undiluted
material at a coverage rate of 1kg/m2
get an approximate dry film thickness of 0.5 mm.
It is important to ensure that each coat is
completely cured before applying subsequent
coats. The second coat should be applied at right
angle to the first at the same coverage rate, to
ensure a full unbroken coating to the substrate.
BAUCOAT HP will achieve its full strength after a
curing period of 7 days.
25 Kg Pails & 200 Kg Drum
1Kg /m² at 0.5 mm thickness.
Two coats will give a combined thickness of 1mm
STORAGE & SHELF LIFE
Store under cover, out of direct sunlight, clear of
the ground on pallets and protect from extreme
temperatures. In tropical climate the product
must be stored in air-conditioned environment
Shelf life is 12 months when stored as above.
As with all construction chemicals products
caution should always be exercised. Protective
clothing such as gloves and goggles shall be
Treat any splashes to the skin or eyes with fresh
water immediately. Should any of the products
be accidentally swallowed, do not induce
vomiting, but call for medical assistance
immediately. There are no known health hazards
associated with BAUCOAT HP.
Clean all the tools with water after use.
Hardened materials can be removed
mechanically only. Allow the waste to cure. Seal
it into a suitable container and bury in landfill as
per local regulations.
Highly Elastomeric Acrylic Waterproofing & Protective Coating
1. Product Description
BAUCOAT HP is single component highly elastomeric, acrylic waterproofing and
2. Substrate Requirement
• All surfaces must be structurally sound, clean, free from dust, oil and any traces of
foreign materials that may affect adhesion of the waterproof coating on the
• Brick, block and concrete walls/ floors must be allowed to cure for a minimum of 4
weeks prior to application of BAUCOAT HP.
• Cement render and screed must be allowed to cure for at least 7 days and finished
to semi-smooth finish with a wood float. After curing, a thorough check on the
soundness in adhesion of the screed and render should be carried out. All
substrate defects should be properly rectified.
• Painted surface must be scrapped to expose the original substrate for the
• The trueness of the background surface required for the substrate beds should be
such that, when checked with a 2m straightedge, any gap under the straightedge
between points of contact does not exceed 3mm.
• Thoroughly dampen the substrate with water and allow access to drain away.
• Incase of metal substrate, rust scales to be removed using wire brush.
• Ensue a minimum slope of 1 in 100 is already provided
3. Application of BAUCOAT HP
• Make sure that all substrate requirements are met, such as temperature, moisture
content of the prepared substrate (preferably below 5%) etc.
• Mix the bucket/drum thoroughly prior to application to remove the sediments.
• Dilute BAUCOAT HP with 20% water to be used as primer coat on the substrate
and allow it to dry for about 3-4 hours.
• Once the surface is dry, clean the surface and apply BAUCOAT HP at 1 kg per
square meter. For spray application, dilute BAUCOAT HP with 5% of water to
reduce the viscosity.
• Allow the surface to dry for 4-5 hours.
• Apply the second coat at 1 kg per square meter in right angle to the first coat.
• Allow the coating to cure fully for 72 hours to achieve its full properties.
• Once the coating is cured completely, it should be checked for its adhesion to the
substrate. For this mark a square of 5cm x 5cm randomly on the surface.
• Cut the square with a knife diagonally across the square. Rip the coating and check
the thickness with Vernier calipers, to see if the dry film has an average thickness
• Once these tests are done, reapply BAUCOAT HP over those portions, in
accordance with the regular procedure.
4. Post Application
• Conduct ponding test by filling up to 50mm of water for 48 hours to ensure leak
Material Safety Data Sheet
1) PRODUCT AND COMPANY IDENTIFICATION Distributed by: BAUTECH Chemical Industries LLC
Tel: +971-67441150 Fax: +971-67441120
P.O. Box 23054, Ajman, United Arab Emirates
2) COMPOSITION / INFORMATION ON INGREDIENTS
Chemical characterization Acrylic Emulsion (CAS No.25085-34-1) Water (CAS No,
7732-18-5) Pigments & additives.
Hazardous ingredients N/A. Ingredients deemed non hazardous
Chemical name HS CODE: 3209.1090
3) POTENTIAL HAZARDS
Primary hazard Non-Flammable & Non Toxic
Secondary hazard May be irritant to skin and eyes contact
4) FIRST AID MEASURES
Eye Contact Wash with plenty of water for at least 15 minutes. If
irritation persists, seek medical attention.
Skin Contact Remove contaminated clothing and wipe affected skin
with dry cloth then wash with soap and water. Seek
medical attention if irritation persists.
Ingestion DO NOT INDUCE VOMITING because of risk of aspiration.
Give 200-300mls (half pint) of water to drink. Seek
immediate medical attention.
NOTE TO PHYSICIANS. Treat observation and supportive measures as indicated
by the patient’s conditions. See section 11 Toxilogical
5) FIRE FIGHTING MEASURES
Extinguishing Media N/A Non flammable
Not to be used None
Combustion products N/A
6) ACCIDENTAL RELEASE MEASURES
Personal Protection during Spill Wear goggles, gloves and overalls. Spillage causes
Precautions to Protect Environment Prevent ingress to drains and water-courses. If polluted
water enters water-courses inform relevant authorities
Spillage Clean Up Methods Absorb spillage with earth or sand.
After spillage / leakage Take up with an absorbent material e.g. sand, sawdust
and collect in a disposal bags.
Please refer to local rules and regulations for disposal.
7) HANDLING AND STORAGE
Usage Precautions Ensure adequate ventilation. Avoid contact with the eyes
and skin. When using DO NOT eat, drink or smoke.
Storage Criteria Keep in cool ventilated area. Keep containers sealed.
8) EXPOSURE CONTROLS / PERSONAL PROTECTION
INGREDIENT. Blend of Water, Styrene Acrylic co polymer pigments and
CAS No. Acrylic Emulsion (CAS No.25852-37) Water (CAS No,
Personal Protective Equipment Wear goggles giving complete eye protection. Wear nitrile
gloves. In cases of insufficient ventilation wear selfcontained respiratory equipment.
Hygienic Work Routines Keep working clothes separate and do not take home.
Use good personal hygiene practices. Wash hands after
9) PHYSICAL AND CHEMICAL PROPERTIES
Form Thixotropic Paste
Color Milky White
Change in physical state No statement possible
Density 1.25 +/- 0.02 kg/ltr
Vapor pressure, mbar (°C) N/A
Solubility in water Water soluble
pH 6 to 9
Boiling Point, °C 100 0 C
Flash Point N/A
Ignition temperature N/A
Thermal decomposition N/A
Explosion limits N/A
VOC content 25 g/lit.
10 STABILITY AND REACTIVITY
Stability Stable under normal conditions.
Materials to Avoid N/A.
Conditions to avoid in use N/A
Hazardous reactions N/A
11) INFORMATION ON TOXICITY
Skin Contact Prolonged skin contact will cause irritation.
12) INFORMATION ON ECOLOGICAL EFFECTS
Environmental Hazards Harmful to aquatic organisms. (R52). May cause harmful
effects to aquatic environment. (R53).
Degradability Not readily biodegradable
Disposal This product and its container must be disposed of as a
hazardous waste. DO NOT empty into drains or
DOT : Not restricted.
TDG : Not restricted for road or rail.
ICAO : Not restricted
IATA : Not restricted
IMDG/IMO : Not restricted
Other Information Regarded as non- hazardous for transport.
Labelling clear indication and identification of materials
R Phrases May cause sensitization to skin contact
S Phrases After contact with skin, wash immediately with water
and soap. Wear suitable PPE’s for protection.
16) FURTHER INFORMATION Whilst the descriptions, designs data and information
contained herein are presented in good faith and
believed to be accurate, it is provided for your guidance
only. Because many factors may affect processing or
application/use, we recommend that you make tests to
determine the suitability of a product for your particular
purpose prior to use. No warranties of any kind, either
expressed or implied, including warranties of
merchantability or fitness for a particular purpose, are
made regarding products described or designs, data or
information set forth, or that the products, designs, data
or information may be used without infringing the
intellectual property rights of others. In no case shall the
descriptions, information, data or designs provided be
considered a part of our terms and conditions of sale.
Further you expressly understand and agree that the
descriptions, data and information given or results
obtained, all such being given and accepted at your risk.
MSDS VERSION: 01
Date: MAY 2018 Last Revision: MAY 2019
- 968 全部视图
- 732 网站视图
- 236 嵌入的视图
- Social Shares
- 0 评论
- 0 Facebook
- 0 Twitter
- 2 126.96.36.199
- 29 www.sab-us.com
- 1 www.google.com
LAVATEX 20003349 视图
طبقات نظام العزل كومبو رووف2020 视图
DCL Product Conformity1595 视图
SAB Trade Mark Certificate1542 视图
SAB Methodology Combo Roof1430 视图
مصطلحات هندسية Geometric terms1420 视图
SAB ® بولي ريثان1415 视图
شمس البوادي - علامة تجارية مسجلة1385 视图
Fosroc Conbextra EPGP1344 视图
Previous work1339 视图
Organizational Char1332 视图